JIS G3461 Grade STB 510 Carbon Steel Seamless Tubes are also known as mild steel pipes and tubes.JIS G3461 Grade STB 510 Tubes are low-cost Low Carbon Steel Tubes with max 025 % carbon content with combination of 100-150 % manganese easy to form and shape .These pipes are manufactured as per JIS Specification and commercially referred as cs pipes or ms pipes.Low Carbon Steel Pipes are not as hard as hig carbon steel pipes,Though carburizing can increase its surface hardness.
Carbon | Silicon | Manganese | Phosphorous | Sulphur | Molybdenum | Nickel | Chromium | Copper | Others |
---|---|---|---|---|---|---|---|---|---|
max 0.25 | max 0.35 | 1.00-1.50 | 0.035 | 0.035 | – | – | – | – | – |
Yield Strength | Tensile Strength | Elongation A5 min | |||
---|---|---|---|---|---|
MPa min | ksi min | MPa min | MPa min | ksi min | Percentage |
510 | – | – | 25 |
DIN | EN | BS | NFA | ASTM | ASME |
---|---|---|---|---|---|
– | – | – | – | – | – |
Execution | Size Range | OD Tolerance | Wall tolerance |
---|---|---|---|
Hot-rolled Tube | OD – 80 mmOD > 80 mmWall < 12 mmWall - 12 mm | ± 0.4 mm± 0.5 % of OD | ± 0.7 mm± (5 % x wallthickness + 0.1 mm |
Hot-rolled peeled tube | All sizesWall < 12 mmWall - 12 mm | + 0.25/- 0 mm | ± 0.8 mm± (5 % x wall thickness+ 0.2 mm) |
Cold Worked tubecold-rolled or cold-drawn | OD < 40 mmOD 40 - 80 mmOD > 80 Wall Thickness < 6 mm Wall Thickness6 - 8 mm Wall Thickness > 8 | + 0.30/- 0 mm*+ 0.35/- 0 mm*+ 0.40/- 0 mm* | ± 0.30 mm± 0.35 mm± 0.40 mm |
The maximum deviation from the straight line is 1 mm on a gauge length of 1000 mm.
The maximum out-of-roundness is 65% of the total outer diameter tolerance.
Component length (mm) | OD 30-100 mm | OD 100-254 mm |
---|---|---|
10-100 | + 1.0/- 0 | + 2.0/- 0 |
100-600 | + 2.0/- 0 | + 3.0/- 0 |
600-1200 | + 3.0/- 0 | + 4.0/- 0 |
1200-5000 | + 5.0/- 0 | + 6.0/- 0 |
All tubes are supplied with clean, square cut ends.Deburring and/or chamfering can be carried out on request.
Tubes are supplied normally without anti-corrosive treatment, but anti-corrosive treatment is available and is carried out on request.
Tubes are bundled as standard, with steel straps into hexagonal bundles with one end flush.Length sorting can be carried out on request. Tubes can also be bundled in multiples. Bundle weights are adjusted as requested by the customer. Each bundle contains tubes from a single cast/heat only.
Each tube is marked with tube type, heat number, steel grade and size. Information is repeated along the whole length of the tube. Other markings, such as stamping, can be made on request. Bundles are also labeled with a tag having info both alphanumeric and by bar code.
Material delivered direct from our mill is labeled in accordance with automotive standard, ie with both alphanumeric and bar code information. Customer specific data can be added on request.
WWP-404c is similar to ASTM A-53 except that Government inspection and continuous identification marking of electric weld and seamless is mandatory. It covers black and galvanized welded and seamless pipe for flanging, bending, and coiling and for use with fresh water, oil, steam, air, and gas on shore plus a limited number of shipboard uses. Sizes 1/8 inch through 24 inch.WWP-406c is a federal specification comparable to ASTM A-120 (withdrawn 1988). Mills can certify that A-120 pipe in a distributor-s stock meets all the requirements of WWP-406c.
C-200 covers black welded and seamless pipe intended for the conveyance of water in sizes 6 inch and larger. Specification prescribes hydrostatic test pressures for sizes of pipe covered. Tensile, flattening, and bending tests are required.
JIS G3461 Grade STB 510 Specification Covers Carbon Steel Pipes for Pressure Service .Mechanical properties of This steel grades can be varied greatly by heat treating. Through a controlled cycle of heating and cooling, certain desired properties are obtained by producing predictable changes in the microstructure of the steel. Our pipe representative will be happy to work with you to develop the information that is required.
FerroPipE is considered as the most Reliable JIS G3461 Grade STB 510 tubes Supplier from India.
JIS G3461 Grade STB 510 Carbon Steel Seamless Pipes are certified with Mill test Certificate in accordance with En 10204 Type 3.1/3.2. Where 3.2 indicates In-stage inspection by independent inspection agencies like TUV, DNV, BVQS, LLOYDS & EIL.
IBR, NACE MR 0175,NACE MR 0103, HIC, IGC, IMPACT are adhered as supplementary testing requirements for JIS G3461 Grade STB 510 which can be fulfilled with a government approved NABL laboratory.
JIS G3461 Grade STB 510 Pipes are supplied in varnished condition in order to prevent formation of rust.
JIS G3461 Grade STB 510 Pipes are used mainly for automobile sectors, interior & exterior architectural structures, water pipe lines, Gas lines, Oil & Gas industries etc.
Ferropipe is india's leading carbon steel pipe stock and alloy steel pipe stock and pipe stockist, pipe suppliers, pipe exporters, importer ,pipe dealers, stockholders, indentor, pipe manufacturers, retailers, wholesaler, pipe distributors, traders, specialized in delivering consignments on time by means of Express Courier Services DHL, FedEx, UPS, TNT, etc. to the remote locations.
Top 9 Grades of JIS Specification Pipes avaiable ex stock.