DIN 17179 Grade TStE 355 Carbon Steel Seamless Tubes
DIN 17179 Grade TStE 355 Specification
DIN 17179 Grade TStE 355 Carbon Steel Seamless Tubes are also known as mild steel pipes and tubes.DIN 17179 Grade TStE 355 Tubes, are low-cost Low Carbon Steel Tubes with max 018 % carbon content with combination of 090 – 165 % manganese easy to form and shape .These pipes are manufactured as per DIN Specification and commercially referred as cs pipes or ms pipes.Low Carbon Steel Pipes are not as hard as hig carbon steel pipes,Though carburizing can increase its surface hardness.
DIN 17179 Grade TStE 355 Properties
Chemical Properties
| Carbon | Silicon | Manganese | Phosphorous | Sulphur | Molybdenum | Nickel | Chromium | Copper | Others |
|---|---|---|---|---|---|---|---|---|---|
| max 0.18 | 0.10 – 0.50 | 0.90 – 1.65 | 0.03 | 0.025 | max 0.08 | max 0.30 | max 0.30 | max 0.20 | Al min 0.020 |
Mechanical Properties
| Yield Strength | Tensile Strength | Elongation A5 min | |||
|---|---|---|---|---|---|
| MPa min | ksi min | MPa min | MPa min | ksi min | Percentage |
| 490 | 630 | – | 22 | ||
Equivalent Designation
| DIN | EN | BS | NFA | ASTM | ASME |
|---|---|---|---|---|---|
| DIN 17179 Grade TStE 355 | – | – | – | – | – |
Materials
- Carbon Steel
- Alloy Steel
- Low Temperature Carbon Steel
- High Temperature Carbon Steel
- Low Temperature Alloy Steel
- High Temperature Alloy Steel
Types of DIN 17179 Grade TStE 355
Pipes
Seamless Pipes
- Cold Drawn Seamless Pipes
- Hot Drawn Seamless Pipes
Welded Pipes
- Electric Resistance Welded(ERW) Pipes
- Continous Welded(CW) Pipes
- Submerged Arc Welded(SAW) Pipes
- Double Submerged Arc Welded(DSAW) Pipes
- Spiral Welded Pipes
- High Frequency Induction(HFI)
- Longitudinally Submerged Arc Welded(LSAW) Pipes
Tubes
Seamless Tubes
- Cold Drawn Seamless Tubes
- Hot Drawn Seamless Tubes
Welded Tubes
- Electric Resistance Welded(ERW) Tubes
- Continous Welded(CW) Tubes
- Submerged Arc Welded(SAW) Tubes
- Double Submerged Arc Welded(DSAW) Tubes
- Spiral Welded Tubes
- High Frequency Induction(HFI)
- Longitudinally Submerged Arc Welded(LSAW) Tubes
Hollow Sections
Pipes
- Boom Pipe
- Culvert Pipes
- Square Pipes
- Round Pipes
- Honed Pipes
Tubes
- Boom Tubes
- Culvert Tubes
- Square Tubes
- Round Tubes
- Honed Tubes
Dimensional Tolerances of DIN 17179 Grade TStE 355
OD/Wall tolerance
Outer diameter and wall Thickness
| Execution | Size Range | OD Tolerance | Wall tolerance |
|---|---|---|---|
| Hot-rolled Tube | OD – 80 mmOD > 80 mmWall < 12 mmWall - 12 mm | ± 0.4 mm± 0.5 % of OD | ± 0.7 mm± (5 % x wallthickness + 0.1 mm |
| Hot-rolled peeled tube | All sizesWall < 12 mmWall - 12 mm | + 0.25/- 0 mm | ± 0.8 mm± (5 % x wall thickness+ 0.2 mm) |
| Cold Worked tubecold-rolled or cold-drawn | OD < 40 mmOD 40 - 80 mmOD > 80 Wall Thickness < 6 mm Wall Thickness6 - 8 mm Wall Thickness > 8 | + 0.30/- 0 mm*+ 0.35/- 0 mm*+ 0.40/- 0 mm* | ± 0.30 mm± 0.35 mm± 0.40 mm |
Straightness
The maximum deviation from the straight line is 1 mm on a gauge length of 1000 mm.
Ovality
The maximum out-of-roundness is 65% of the total outer diameter tolerance.
Standard length tolerances
| Component length (mm) | OD 30-100 mm | OD 100-254 mm |
|---|---|---|
| 10-100 | + 1.0/- 0 | + 2.0/- 0 |
| 100-600 | + 2.0/- 0 | + 3.0/- 0 |
| 600-1200 | + 3.0/- 0 | + 4.0/- 0 |
| 1200-5000 | + 5.0/- 0 | + 6.0/- 0 |
Delivery Executions of DIN 17179 Grade TStE 355
Tube Ends
All tubes are supplied with clean, square cut ends.Deburring and/or chamfering can be carried out on request.
Tube surface
Tubes are supplied normally without anti-corrosive treatment, but anti-corrosive treatment is available and is carried out on request.
Protection
- Black and Bare
- External Varnished with Black or Clear LAcquer
Mill test certificate
- MTC is issued in accordance with EN 10204.
Packaging
Tubes are bundled as standard, with steel straps into hexagonal bundles with one end flush.Length sorting can be carried out on request. Tubes can also be bundled in multiples. Bundle weights are adjusted as requested by the customer. Each bundle contains tubes from a single cast/heat only.
Marking
Each tube is marked with tube type, heat number, steel grade and size. Information is repeated along the whole length of the tube. Other markings, such as stamping, can be made on request. Bundles are also labeled with a tag having info both alphanumeric and by bar code.
Labelling
Material delivered direct from our mill is labeled in accordance with automotive standard, ie with both alphanumeric and bar code information. Customer specific data can be added on request.
Dimensional Standards of DIN 17179 Grade TStE 355
FEDERAL
WWP-404c is similar to ASTM A-53 except that Government inspection and continuous identification marking of electric weld and seamless is mandatory. It covers black and galvanized welded and seamless pipe for flanging, bending, and coiling and for use with fresh water, oil, steam, air, and gas on shore plus a limited number of shipboard uses. Sizes 1/8 inch through 24 inch.WWP-406c is a federal specification comparable to ASTM A-120 (withdrawn 1988). Mills can certify that A-120 pipe in a distributor-s stock meets all the requirements of WWP-406c.
A.W.W.A.
C-200 covers black welded and seamless pipe intended for the conveyance of water in sizes 6 inch and larger. Specification prescribes hydrostatic test pressures for sizes of pipe covered. Tensile, flattening, and bending tests are required.
ASME
- B31.1 Code for pressure piping.plants, and industrial plants.
- B31.2 Fuel Gas Piping.
- B31.3 Petroleum Refinery Piping.
- B31.4 Liquid PetroleumTransportation Piping Systems.
- B31.5 Refrigeration Piping.
- B31.7 Nuclear Power Piping
- B31.8 GasTransmission and Distributing Piping Systems. Covers design, fabrication, installation, inspection, testing, and the safety aspects of operation and maintenance of gas transmission and distribution systems.
ANSI (ASME)
- B36.10 American Standard for Wrought-Steel and Wrought-Iron pipe. Designates dimensions, weights, and schedule numbers for welded and seamless pipe. Schedules 10 through Schedules Double Extra Heavy (DXH/XXH).
- B36.19 American Standard for Stainless Steel Pipe. Designates dimensions, weights, and schedule numbers for welded and seamless Stainless Steel Pipe, Schedules 5 through Schedules 80.
A.A.R.
- M-111 covers black and galvanized welded and seamless pipe intended for coiling, bending, flanging, and other special purposes and is suitable for welding. Purpose for which pipe is intended should be stated on orders. M-111 is comparable in most requirements to ASTM A-53.
- M-130 covers black and galvanized welded and seamless pipe for ordinary uses in steam, water, gas, and air lines. Sizes 1/8 inch through 12 inch. Pipe to this specification is not intended for close coiling, bending, or high temperature service. M-130 is comparable in most requirements to ASTM A-120.
DIN 17179 Grade TStE 355 standard applies to seamless circular tubes subject to special requirements and made from the fine grain structural steels .These tubes are pre-dominantly used in the construction of pressure vessels, chemical plant, pipework and for general mechanical engineering purposes. They are designed for operating temperatures not exceeding 400-C and, in the as delivered condition normally exhibit a minimum yield strength of between 255 and 460N/mm_.Our pipe are been supplied in both Plain Square cut,Deburred Ends or Bevelled End. This can be provided with Mill Standard Varnished ,stencilled and bundle Strapped with end caps fitted. Each Bundle is packed according to the customer requirement for export orders.
FerroPipE is considered as the most Reliable DIN 17179 Grade TStE 355 Pipes Supplier from India.
DIN 17179 Grade TStE 355 Carbon Steel Seamless Tubes are certified with Mill test Certificate in accordance with En 10204 Type 3.1/3.2. Where 3.2 indicates In-stage inspection by independent inspection agencies like TUV, DNV, BVQS, LLOYDS & EIL.
IBR, NACE MR 0175,NACE MR 0103, HIC, IGC, IMPACT are adhered as supplementary testing requirements for DIN 17179 Grade TStE 355 which can be fulfilled with a government approved NABL laboratory.
DIN 17179 Grade TStE 355 Tubes are supplied in varnished condition in order to prevent formation of rust.
DIN 17179 Grade TStE 355 Tubes are used mainly for automobile sectors, interior & exterior architectural structures, water pipe lines, Gas lines, Oil & Gas industries etc.
Ferropipe is india's leading carbon steel pipe stock and alloy steel pipe stock and pipe stockist, pipe suppliers, pipe exporters, importer ,pipe dealers, stockholders, indentor, pipe manufacturers, retailers, wholesaler, pipe distributors, traders, specialized in delivering consignments on time by means of Express Courier Services DHL, FedEx, UPS, TNT, etc. to the remote locations.
Here is a list of 78 different DIN Specification Pipes