ASME SA 53 Grade B Carbon Steel Seamless Pipes are Medium Carbon Steel Pipes with 0.3 % carbon content with combination of 1.2 % manganese. These Pipes are most commonly used for general purpose applications worldwide. ASME SA 53 Grade B Pipes are ductile and strong Pipes with long wearing properties. These Pipes are manufactured as per ASME Specification and commercially referred as carbon steel Pipes.
Carbon | Silicon | Manganese | Phosphorous | Sulphur | Molybdenum | Nickel | Chromium | Copper | Others |
---|---|---|---|---|---|---|---|---|---|
0.3 | – | 1.2 | 0.05 | 0.045 | 0.15 | 0.4 | 0.4 | 0.4 | V 0.08 |
Yield Strength | Tensile Strength | Elongation A5 min | |||
---|---|---|---|---|---|
MPa min | ksi min | MPa min | MPa min | ksi min | Percentage |
415 | – | 60 | – |
DIN | EN | BS | NFA | ASTM | ASME |
---|---|---|---|---|---|
DIN 17175 Grade St 35-8 | – | NFAA 49-215 Grade TU 37-c | ASTM A53 Grade B | ASME SA 53 Grade B | – |
All tubes are supplied with clean, square cut ends.Deburring and/or chamfering can be carried out on request.
Tubes are supplied normally without anti-corrosive treatment, but anti-corrosive treatment is available and is carried out on request.
ASME SA 53 Grade B Carbon Steel Seamless Pipes are bundled as standard, with steel straps into hexagonal bundles with one end flush.Length sorting can be carried out on request. Tubes can also be bundled in multiples. Bundle weights are adjusted as requested by the customer. Each bundle contains tubes from a single cast/heat only.
ASME SA 53 Grade B Carbon Steel Seamless Pipes is marked with tube type, heat number, steel grade and size. Information is repeated along the whole length of the tube. Other markings, such as stamping, can be made on request. Bundles are also labeled with a tag having info both alphanumeric and by bar code.
ASME SA 53 Grade B Carbon Steel Seamless Pipes delivered direct from our mill is labeled in accordance with automotive standard, ie with both alphanumeric and bar code information. Customer specific data can be added on request.
WWP-404c is similar to ASTM A-53 except that Government inspection and continuous identification marking of electric weld and seamless is mandatory. It covers black and galvanized welded and seamless pipe for flanging, bending, and coiling and for use with fresh water, oil, steam, air, and gas on shore plus a limited number of shipboard uses. Sizes 1/8 inch through 24 inch.WWP-406c is a federal specification comparable to ASTM A-120 (withdrawn 1988). Mills can certify that A-120 pipe in a distributor-s stock meets all the requirements of WWP-406c.
C-200 covers black welded and seamless pipe intended for the conveyance of water in sizes 6 inch and larger. Specification prescribes hydrostatic test pressures for sizes of pipe covered. Tensile, flattening, and bending tests are required.
ASME SA 53 Grade B pipes specification covers seamless and welded black and hot-dipped galvanized steel pipe in NPS 1-8 to NPS 26 [DN 6 to DN 650] .ASME SA 53 Grade B Carbon Steel Seamless Pipes includes sizes under NPS 2 [DN 50], when the wall thickness is lighter than the lightest shown for a given diameter, use the test pressure given for the lightest wall thickness of the table for the diameter involved. The test pressure has been arbitarily assigned. Test pressures for intermediate outside diameters need not exceed those for the next larger listed size.
FerroPipE is considered as the most Reliable ASME SA 53 Grade B Pipes Supplier from India.
ASME SA 53 Grade B Carbon Steel Seamless Pipes stockist in Mumbai, India.Ferropipe stocks a complete range of IBR Certified ASME SA 53 Grade B Carbon Steel Seamless Pipes in outer diameter tube sizes ½”-24” and Nominal bore NB sizes 15NB-600NB in Mumbai, India. Exporting Carbon Steel Pipes and Alloy Steel Pipes to countries worldwide including IRAN, IRAQ, KUWAIT, QATAR, South Africa, Nigeria, Saudi Arabia, Australia, Canada & Mexico.
In addition to the marking specified in Specification A 999/A 999M, the marking should have the length, an additional symbol -S-, if ASME SA 53 Grade B Carbon Steel Seamless Pipes conforms to any of the Supplementary Requirements S1 to S6, the schedule number of the pipe is ordered to a schedule number viz. SCH 5,10,20,30,40,60,80,100,120,140,160,XS, XXS, STD, and the heat number of or manufacturer-s number by which the heat can be identified as per ASME SA 53 Grade B.
Wall Thickness : the minimum wall thickness at any point or end on ASME SA 53 pipes and tubes shall not be greater than 12.5% under the nominal thickness specified.
Inner Diameter: For pipe ordered in inside diameter, the inside diameter shall not vary more than ñ 1% from the required/specified inside diameter.
The Manufacturer shall provide Material Test certificate of inspection to the purchaser stating that the material has been manufactured, sampled, tested, and inspected in accordance with ASME SA 53 Grade B( including year of issue), and has satisfied all the requirements of ASME SA 53.
Pipes and Tubes manufactured as per ASME SA 53 Grade B are certified with En 10204 Type 3.1/3.2. IBR,NACE,HIC,IGC,IMPACT are adhered as supplementary testing requirements.
The minimum elongation in 2 in. [50 mm] shall be that determined by the following equation:
e = 625 000 [1940] A0.2/U0.9
where:
e = minimum elongation in 2 in. [50 mm] in percent rounded to the nearest percent
A = cross-sectional area of the tension specimen, rounded to the nearest 0.01 in.2 [1 mm2], based on the specified outside diameter or the nominal specimen width and specified wall thickness. If the area calculated is equal to or greater than 0.75 in.2 [500 mm2], then the value 0.75 in.2 [500 mm2] shall be used
U = specified tensile strength, psi [MPa]
The combination of Copper, Nickel, Chromium, Molybdenum & Vanadium Shall not exceed 1.00%
ASME SA 53 Grade B shall conform to a carbon equivalent (CE) of 0.50 maximum as determined by the following formula:
CE = %C + %Mn/6 + (%Cr + %Mo + %V)/5 + (%Ni + %Cu)/15 .
A lower Carbon equivalent ration maximum may be agreed upon between the purchaser and the producer.
The Carbon equivalent ration shall be reported on the MILL test report.
Ferropipe is india's leading carbon steel pipe stock and alloy steel pipe stock and pipe stockist, pipe suppliers, pipe exporters, importer ,pipe dealers, stockholders, indentor, pipe manufacturers, retailers, wholesaler, pipe distributors, traders, specialized in delivering consignments on time by means of Express Courier Services DHL, FedEx, UPS, TNT, etc. to the remote locations.